Toro 1800 18-Inch 12 Amp Electric Curve Snow Thrower #38025 Immediately

I don't know if I got a defective one or what, but I used it once in 12 inches of snow and it worked great. Good throw distance and whatnot. My one complaint is that since it is so light it tends to slide sideways pretty easily.

The second storm, about 6 inches today, the blade stopped spinning and there was a whirring sound. I took off the side plate (which was bent and not installed properly) and it turns out the drive belt came off. So, I put the drive belt back on, but it will not stay in place anymore. The thrower goes about 5 feet and that's it.

I am really confused about why this snow thrower got so many good reviews but mine stunk. Judging by the incorrectly installed side plate and all, I think I may just have gotten a dud. Anyway, I am now soured on this model and will buy a gas thrower.

Incidentally, if you do decide to buy this item, Home Depot has a Rigid 100-foot 15 Amp sub zero temp extension cord for $65. It is a pretty good deal.Get more detail about Toro 1800 18-Inch 12 Amp Electric Curve Snow Thrower #38025.

Toro 1800 18-Inch 12 Amp Electric Curve Snow Thrower #38025 Best Quality

This is perfect and I wish I brought this sooner! I can do all my sidewalks and driveway in less then 20 minutes.Get more detail about Toro 1800 18-Inch 12 Amp Electric Curve Snow Thrower #38025.

Toro 1800 18-Inch 12 Amp Electric Curve Snow Thrower #38025 Get it now!

After seeing that most people love the Toro 1800, I decided to get it for my wife. Seeing also that a significant minority got defective units, I was hoping mine would turn out defective as well, so I could take it apart and find out why (yes, this is how engineers go through life). Got it home, it worked great for 20 seconds, then the impeller stopped turning even though the motor continued. YESSSS!!!

It wasn't a slipped belt, but a more subtle problem. See p. 9-10 of the manual, "Replacing the Rotor." There is a note just above step 6: "When mounting the coupler to the drive hex, align the coupler tabs to the inside." Well, it was installed backwards, i.e. aligned to the outside. That created a situation where the plastic impeller would turn until it encountered significant resistance, then it would slip out of the coupler and freewheel.

The failure mode above matches several 1-star reviews I've seen on this product. If you are reasonably handy, check for this assembly defect. You may be able to rescue your purchase. Once fixed, the unit performed in 4-star mode and my wife is now a happy camper.Get more detail about Toro 1800 18-Inch 12 Amp Electric Curve Snow Thrower #38025.

Toro 1800 18-Inch 12 Amp Electric Curve Snow Thrower #38025 Buy Now

For two years, I've been growing increasingly frustrated over the fact that the belt on my Powercurve 1800 (which I have only used 5 - 6 times over the past 3 years) kept falling off. I called Toro for any ideas on what might be causing this and they were of no help whatsoever. So, I went to my local Toro dealer who quoted me just over $200 for repairs. I was just about to take the snowblower to the curb when I decided to take some time to figure out the problem. After all, it cost me $[...] on Amazon...I was determined to try to get my money's worth.

After nearly an entire Saturday afternoon later, I'm pleased to offer a solution. Here it is:

1.) First, go here for the parts diagram: https://www.shoptoro.com/Comergent/en/US/adirect/toro?cmd=ToroOnlineViewDrawing

This will help understand what parts I am talking about.

2.) First, Begin by taking off the black side covers on each side of the snow blower. There should be 3 screws holding each cover in place.

3.) Next, if your belt has fallen off, put it back on. This will take some effort but easily done by rotating the belt and using force so that it wraps around the pully.

4.) Next, examine the other side of the blower...the side without the belts. Look for the center spindle...(mine was gold in color). You will see a screw that can be turned with a rather large allen wrench.

5.) With one hand, hold the white plastic pully...part 41 in the diagram.

6.) With the other hand, insert the allen wrench and turn part 53 until very tight. The fact that part 53 has become loose is the problem.

7.) You should be good to go as this will secure and tighten the pully and will prevent the belt from falling off on the other side...it is that simple.

Let me say, Toro's support was terrible. I will think twice before buying another Toro product. Shame on the Toro dealer that wanted $200+ to repair this.

For those having this problem, I hope this provides a solution for you.

Get more detail about Toro 1800 18-Inch 12 Amp Electric Curve Snow Thrower #38025.